PulseGuard Pulsation Dampeners

Fluid Flow Control Animations
PulseGuard Pulsation Dampeners
Contact PulseGuard
 

Pulsation Dampener part number that matches Multiplex "Power" Pump

Pulsation Dampener Size Selection Tables for piping systems where the flow is from a multiplex power pump.

1. Pulsation dampeners listed below are from 1000s of "off the shelf" inventory pulse dampers for preventing pipe systems from converting power pump flow fluctuation into pressure pulsation. Call toll free 1-888-DAMPERS (326-7277) for discounts, etc. Choose a pulse damper matching your pump connection size, for standard dampening. Or allow us to calculate for you, from your smoothness required and your system data.
2. Where there is no occupational health and safety need for in place flush through before servicing, nor any process requirement for constant temperature, or first in first out need to control residence time, not even clean before changing liquids it is still least expensive to use a standard twin connection dampener , & save a "T". Use the other connection for the system drain, relief valve, or branch line. Waveguard and dampeners for frequencies above 10Hz., and or systems in which pipe-run or tube nodes are less than 290 meters /950ft have to be "Flow-Through"

Pulsation dampeners for Suction Systems, No N2 or Air Pre-Fill required. Remove volumetric acceleration head losses.
Pulsation dampeners for Suction Systems, No N2 or Air Pre-Fill required. Remove volumetric acceleration head losses.

Pulsation dampeners with Ceramics or with orifices. No Moving Parts, No N2 or Air Pre-Fill required.
Pulsation dampeners with Ceramics or with orifices. No Moving Parts, No N2 or Air Pre-Fill required.
Pulsation Interceptor/Isolators, liquid in bladder. Piping bases maintain pipe integrity, weld piping base permanently in system. Proven 300% more high frequency performance and flow fluctuation removal too.
Pulsation Interceptor/Isolators, liquid in bladder. Piping bases maintain pipe integrity, weld piping base permanently in system. Proven 300% more high frequency performance and flow fluctuation removal too.
No flow reversal pressure loss in a single connection. Perfect suction acceleration head loss recovery. Liquid side up prevents bubble collection, stops pump “knock”.
No flow reversal pressure loss in a single connection. Perfect suction acceleration head loss recovery. Liquid side up prevents bubble collection, stops pump “knock”.
for Discharge - Available at extra with single connection, no smoothness guarantee at high frequency.
for Discharge - Available at extra with single connection, no smoothness guarantee at high frequency.
Pulsation Dampeners - PipeGuard Low Pressure
for Suction - The original 1965, one piece molded gas bags, in all stainless shells from the originators. Available connections to 15,000 psi with GL / SBL Hubs, or Autoclave/PPI. For use in externally corrosive environments.
The original 1965 One piece molded gas bags, in all stainless hells from the originators. Available connections to 15,000 psi with GL / SBL Hubs, or Autoclave/PPI. For use in externally corrosive environments. See http://www.accumulators-hyd.com
3. *The question mark “?” = letters, showing your choice of compatible gasket material, add the letter to ordering part number – N= Buna N, E= EP, (H= Hypalon, V= FluoroCarbon, additional cost) A20= Alloy20, H22= Hastrelloy22, Ti2= Titanium 2, Tan= Tantalum, Zir= Zirconium, DSS= duplex stainless steel, SDSS= super duplex stainless steel.
When you see a pulsation dampener or a pump of particular interest, please request literature dedicated to that subject.


PulseGuard Pulsation Dampeners
Dampeners that do, flow goes through but pressure pulsation does not.

PulseGuard pulsation dampeners are designed to address pressure pulsation, which is caused by the resistance of the system to flow. Therefore our dampeners focus on the system related responsibility and are less related to pump liability.

 



Fluid Flow Control Pulsation Dampeners